Facade thermal insulation

Application Cement-free, dispersible putty designed for the Capatect KD System 600 insulation system. It can be used as a renovation tile. Suitable for mounting protective corner profiles. On highly absorbent substrates it can be used as an adhesive.
Butyl sealing tape with a centrally split and overlapping release liner. The fleece allows a good adhesive bond with construction chemical substances. Backing: Polypropylene non-woven Coating: Self-adhesive butyl rubber, permanently elastic and resistant to aging.
Application To seal the connection between the Capatect system and other building elements, e.g. windows, balconies, roof cornices, etc. Properties permanently flexible (very good shape memory) adaptable to fugues with large dimensional tolerances does not require pre-treatment of the side surfaces of the fugue does not react with metal, concrete, wood,...
Intended use For the formation of vertical expansion joints within the Capatect ETICS A and B. Type E: for flush joints Type V: for joints in interior corners Property Expansion joints can be precisely pre-worked weather-resistant UV-resistant can be painted over efficient execution in one operation suitable for all insulation thicknesses with pull-off...
Adhesive and grout for the installation of Meldorfer flat veneers in the exterior and interior in the Capatect facade systems. Application Ready-to-use mortar for the bonding and grouting of Meldorfer flat veneers. Substrate pretreatment see technical data sheet Characteristics A2-s1, d0 according to DIN EN 13501-1 (non-combustible) high initial...
Intended use Plastic profile with integrated fabric strip for a decoupled connection between plaster and on-site laminations. Property Plastic mounting profile Decoupled connection option for on-site laminations Accurate recording in one flight by connector mounting Targeted water management Packaging/Container sizes Cardboard box of 25 pieces Colour...
CAPAROL Capatect-Rolleck
Corners and strips

CAPAROL Capatect-Rolleck

Application For finishing the edges of corners with sharp or flared angles within Capatect systems. Properties 125 x 125 mm fiberglass mesh profile with inner plastic cutter The arms of the angle bar are not connected rigidly, which allows for individual fit in the case of sharp and bifurcated corners Edges can be precisely prepared Prevents the mesh from...
Corners and strips

CAPAROL Capatect Sturzeckwinkel

Description / Material Preformed glass fabric profile for simultaneous use as an inner corner as well as a diagonal reinforcement. Projection: 10cm/20cm/30cm Property Alkali resistant Schiebefest High tensile strength Plasticizer-free Mesh size 4 x 4 mm
Application For the performance of thin layers of putty and plaster in insulation systems in the system with mineral wool and Styrofoam. Also for use on concrete, old mineral plasters, limestone-cement and cement sludge groups PII and PIII. Unsuitable are substrates with salt blooms, plastic and wood substrates, as well as heavily mechanically loaded...
Product description CT 137 ceresit plaster is used for the production of thin-layer plaster on concrete substrates, conventional plasters, gypsum substrates and on gypsum boards, gypsum fiber boards, etc. It can be used as a facade cladding in ceresit systems, insulating the external walls of buildings by the light-wet method using foamed polystyrene...
Destination:Used, among others, as a surface treatment in systems: in the seamless insulation system Capatect CLASSIC B, on uncoated concrete, on Matt bearing surfaces painted with dispersion paints, on mineral bearing surfacesApplication surface:Uncoated concrete, primer plasters, mineral surface plastersAdditional information:Do not use on surfaces with...
Application For the performance of weather-resistant coatings covering and bridging cracks on facade surfaces and concrete surfaces, as well as for the protection of substrates from adverse weather conditions and aggressive air pollution. Properties Water-based, environmentally friendly, low odour Weather resistant Anti-CO2-sd CO2 > 50 m...

MOTIVE PU foam gun mini

090 129
Popular model of the gun made of plastic and metal. For application of foams of typical screw containers.

MOTIVE PU foam gun

090 126
The gun is designed for the application of mounting foams for professional use in construction during insulation and finishing works. A large knob allows you to quickly and accurately adjust the foam flow and a nickel-plated metal body prevents it from sticking.

MOTIVE Cutting mill for styrofoam

080 202
Made of plastic. For cutting slots in insulating materials under the embedding of caps. Suitable for drills or screwdrivers.
Wool and Styrofoam knife with 280mm stainless steel blade. Designed for cutting hard wool-blade type "saw" and soft-blade type "wave". Knife holder two-component. The total length of the knife is 415 mm. It has a material holster with the possibility of fixing at the waist.
Wool and Styrofoam knife with 280mm stainless steel blade. Knife designed to cut hard wool "saw" and soft "wave". Knife holder two-component. The total length of the knife is 415 mm.
Showing 1-24 of 40 item(s)
Product added to wishlist
Product added to compare.

This website use cookies to increase page performance.